PDF COMPLETE MANUAL: mini-arcade-for-raspberry-manual-v0-0
Vinyls: HERE 3d PARTS for SOLID EGDE: HERE 3d IGS & Step. HERE Only Assembly & Fabrication Drawings:drawings
Why this cabinet?
As a amateur builder of Arcade Machines, I found some problems in typical machines, machines like the “originals”.
“Original Arcade” are:
– Big. Only few people could have one of this machines in their houses without space problems.
–Expensive. You need lots of material, and this turn the machine really expensive.
–Difficult to build. For make the “typical salon arcade” you need many tools, which rarely anybody have.
For all this reasons I build this arcade. My “Mini-Arcade” solves this problems and add more interesting aspects.
This are the main characteristics of “Mini-Arcade” are:
-Small. The machine has the minimum sizes for be comfortable and allow to install a 10″ screen in 16:10 or 16:9 format.
-Easy to do. You don’t need to cut “hard” wood, or do difficult cuts. All the fabrication process is easy to do, and you are able to do it with a few tools.
-Great quality. When the machine is assembled, it shows really great, and rigidity of the structure is very good.
-Adaptable. You can use this cabinet in every country or with any raspberry and with any screen size. Don’t matter the electric voltage of you county, the type of raspberry or the screen you will use. You can adapt it easily.
-Convenient. You can accede to the Raspberry easily. It makes easy to load games o change the Sd card connected or add new wifi or Bluetooth USB.
-Clean. All the electric installation is situated in the same place. This makes an electrical installation really clean , without all kind of wires circuits around. Removing only 6 screws you can extract the support with all the electric supply.
-Cheap. All the material are quite cheap. You can build this machine for 150e apx. The material of the cabinet are cheap and easy to found. And the as “cpu” you will use a Raspberry, the cheapest Raspberry costs only 5€ and the most expensive 40€.
– Approximately 1,2m² of 5mm thickness wood.
-1,5m length of 13x13mm wood profile
-Plate of methacrylate 162 x 280.
– Screws 3×12 / 3×19.
-Drills & drill bits of different sizes.
-Some drawings have sizes with rounded by a circle, that’s why this sizes are going to change depending on your Magnetic enclosure, your hinges or joypad.
|Side Right||1||Screen Saver||1|
|Joypad Panel||1||Nut M2.4||14|
|P01||Left and right Sides|
|P02||Bottom 1 / Bottom 2 / Marque / Screen Suport / Top Fan|
|P03||Screen suport / Front joypad|
|P04||Bottom 1 / Bottom 2 / Marque / Screen Suport / Top Fan|
|P05||Rear L / Rear R / Pcb’s Support|
|P07||Guide 6/ Guide 4 / Column Joypad|
You can see the drawings in the manual appendix.
-You don’t need to use wood glue for make the cabinet assembly. You only need it for make some parts, but if you are joining the cabinet and you will use glue, you can do it, excepting the next parts:
Bottom 1 and Bottom 2. This parts have to be free of glue because they should provide access to joypad (bottom1) and for extract PCB support (bottom2)
Let me repeat you, you don’t have to use, use it only if you want, except in the indicated parts.
– Remember that when you do the Joypad Assembly you have to do the holes for pad fixation.
|Ms02||Joaypad & Screen Assembly|
|M04||Pcb’s Suport & bottom|
You can see the drawings in the manual appendix.
-The painting process could (if you want to paint it) could be after, o before the assembly. It’s up to you. I personally prefer do it after the assembly, because the paint will cover some joins.
-If you want to vinyl the cabinet, is REALLY IMPORTANT TO PAINT IT WITH LACQUER OR VARNISH THE WOOD. If you try to apply the vinyl without paint, or painting it with spray paint, the vinyl won’t be fixed enough and they will be take off.
– Vinyl: The best moment for the vinyl installation is when the assembly is done, and the cabinet is painted. Normally is better install the vinyl AFTER buttons because the buttons cover the vinyl.
Note: You can find different vinyl designs in http://www.N3dSTOR.com if you aren’t interested in design one.
– Measure your screen size and position and paint the methacrylate screen saver.
You can get more information in the drawing P06
-This electronic diagram and this inventory are only ORIENTATIVE.
In my opinion it’s a good example to follow, but you can do anything you want in PCB support in the cabinet. The cabinet design admit all type of electronics distributions.
-For fix the PCB’s I use an hexagonal spacer of nylon with his nuts and screws. I recommend it.
-Now is the moment of measure the diameter of the “power connector” and on/off switch and drill the position when you will place it.
– When your select your Raspebrry PI position, take in count the necessary separation for his connectors
EXAMPLE OF PC’S SUPPORT POSITIONED WITH ELECTRIC INSTALATION
Thanks to: Everybody who have read this manual, and especially if you want to contribute and send me your comment, I’ll say thank you in advance, every comment it’s welcome. email: firstname.lastname@example.org
3D ASSEMBLY: If you are interested in 3d parts, you can find it in my webpage http://www.N3dSTOR.com
Thanks to every reader
Remember yhat you can see a video in makking stuff section¡ Thanks to every body¡
Desinged in Solid Edge